Steril Air Vietnam Sterilair Vietnam - Hệ Thống Đèn Diệt Khuẩn - Đèn Tia Cực Tím - Đèn Hồng Ngoại - Uv Lamp
Liên hệ
D3 , Kdc Miếu Nổi, Đinh Tiên Hoàng, P.3 , Q.bình Thạnh
Công ty TNHH TM DV Anh Nghi Sơn
(ANS Vietnam) xin gửi đến quý khách hàng lời chúc sức khỏe và lời chào trân trọng, sự hưng thịnh và ngày càng phát đạt.
Chúng tôi là một trong những Công ty hàng đầu chuyên cung cấp máy móc, thiết bị cho ngành công nghiệp, điện công nghiệp và điều khiển tự động của các hãng nổi tiếng ..balluff Vietnam,Baumer Vietnam,Bei Encoder Vietnam ,Crouzet Vietnam, Kuebler Vietnam , Koganei Vietnam,Celduc Vietnam,Epulse Vietnam,Crydom Vietnam, Raytek Vietnam,Ircon Vietnam ,MTS Vietnam, Kimo Vietnam, Pilz Vietnam, Status Vietnam, newall vietnam, sterilair vietnam, Univer Vietnam,Masibus Vietnam, Elap Vietnam, Setra Vietnam, Suntronix Vietnam, WiseVietnam, TMTeck Vietnam, dakotainstruments Vietnam, FIC Vietnam, elap encoder vietnam, Flowmeters Vietnam, Conch Vietnam, unipulse vietnam, Tival sensors Vietnam, Divus Vietnam, RKC Instrument Vietnam, Conch Vietnam, Automation, Novotechnik Vietnam, Vaisala Vietnam, Ametek Vietnam Jenco Vietnam, Microdetector Vietnam, MTS Sensor, Balluff sensor, Gems sensor Vietnam, Lion Precision Vietnam, Arkon Vietnam, Microsonic Vietnam,Osukl Vietnam,Proxitron Vietnam,JJ Automation Vietnam,Offshore vietnam Brooks Instrument Vietnam,Sensormation Vietnam, Fraba Vietnam, Posital Vietnam,Bernstein Vietnam, Dwyer Instruments, Dwyer Instruments,univer cylinder vietnam, Banico Controls Vietnam, Hopeway Vietnam, IMR Vietnam, Reloca Comat Vietnam, Metalwork Vietnam,Posital Vietnam, Micro Process Controls, Jelsystem Vietnam, wise vietnam......
Xin gửi đến quý khách thông tin của sản phẩm sau:
| Steril Air | ES2000 product range |
| sterilAir ES2036 duo- and duo flex-type air-duct modules can easily be retrofitted and incorporated in already-existing air ducts. The recently developed UVGI software is used here for optimal layout of the UVC airflow system. | |
| Steril Air | ES2000 flex installation kit |
| sterilAir ES2000 flex installation series UVC disinfection units broadly correspond to the ES2000 series units. | |
| In contrast to that of the sterilAir ES2000 device, however, the angle position of the tube holder in the ES2000 flex version is variable, allowing optimal adaptation of the unit to the given dimensions of a pre-existing air duct. It is therefore unnecessary to consider a tube-dependent minimum headroom | |
| Steril Air | EF2000 installation kit |
| With this module sterilAir offers a flexible, multifunctional system for installation in liquid tanks and air conditioning systems or chambers. | |
| The big advantage is that the lamp body can be simply inserted in the disinfection area from outside of the system. In contrast to other systems (e.g. ES2000) it is not necessary to use service doors or to dismount components to reach the installation point. | |
| Steril Air | LSK2030 |
| The LSK series of air-recirculation units enables the disinfection of room air in areas where direct or indirect UV emission must be avoided under all circumstances. Whether patient rooms, waiting rooms, laboratory workstations, isolation wards or offices: The system safely and reliably disinfects all forms of vegetative and/or generative micro-organisms | |
| Steril Air | UVR2250-2 |
| The UVR model range is divided into two systems: | |
| UVR2250-2 for air flow rates up to 220 m³/h | |
| UVR2250-4 for air flow rates up to 450 m³/h | |
| The devices are advantageous due to a very high UVC doses and are therefore adapted for the deactivation of particularly resistant germs and spores. They are consisting of a of stainless steel tube and are primarily for applications in production and maturing rooms, as well as storehouses and cooling chambers. The smaller UVR2250-2 system has a total weight of 16 kg and is with a noise level of 42 dB(A) particularly silent. The device, which is also suitable for humid rooms, can be disassembled in its components for cleaning and maintenance purposes. | |
| Steril Air | UVR2250-4 |
| The UVR model range is divided into two systems: | |
| UVR2250-2 for air flow rates up to 220 m³/h | |
| UVR2250-4 for air flow rates up to 450 m³/h | |
| The disinfection device UVR2250-4 is the more powerful version of the UVR2250-2. This higher quality model is equipped with four UVC tubes and has a power input of 250 W/1190 mA. It is predestined for highly contaminated and large volume halls due to an air flow rate of 450 m3/h and a very high UVC dose. The device, which is also suitable for humid rooms, can easily and quickly be disassembled in its components for cleaning and maintenance purposes | |
| Steril Air | D2000 ceiling emitters |
| D2000-type ceiling emitters are ready-for-connection units available in two sizes: The standard D2036 version measures 905mm in length, whilst the compact D2018 version measures just 430mm. Both models have an instrument height of 100mm, and with a width of just 35mm are exceptionally slim. The units may be equipped with different tubes. They bear the CE mark, and are compliant with VDE and ENEC standards. | |
| The units may optionally be equipped with an inversely switched movement alarm, which automatically switches off the unit in the event of spatial movement. | |
| Steril Air | DB2000 |
| The DB 2000 series is developed as ceiling ermitters. | |
| The extended stainless steel radiation protection cover reliably prevents direct emission aimed downwards. Persons entering the storeroom are thus protected from intensive radiation, and the direct irradiation of products does not occur, in keeping with the Food Irradiation Ordinance. | |
| Steril Air | WR2000 wall emitter |
| Manufactured from high-grade stainless steel and other corrosion-resistant materials, this disinfection system consists of a device with fixture, a reflector and a protective grille positioned in front of it. The protective grille is provided with a UV-absorbing coating through which a highly concentrated horizontal UVC-ray ceiling is generated above the heads of those present. | |
| The lowest energy costs coupled with high efficiency and long tube-change intervals are the outstanding features of this type of unit. | |
| Steril Air | WB2000 wall emitter |
| The WB 2000 series is developed for less frequented rooms and is equipped with an optimized reflector element to release highest amount of UVC radiation into the over head area. | |
| The system has a protection degree of IP54 and therefore can be used under humid room conditions. Several dimensions and different types of UVC-tubes allow the perfect choice due to given room sizes and temperature range. | |
| Steril Air | SWR2036 Airlock- /wall emitter |
| The SWR2036 is a combined airlock-/wall emitter for continuous indoor-air disinfection. The system is mounted above the door, and generates highly concentrated UVC radiation both on the horizontal and on the vertical. The concentration of rays is achieved via a built-in reflector with a protective grille in front of it. | |
| This dual function makes the device clearly superior to any UV-based portable device working with a closed chamber according to the air-circulation process! | |
| Steril Air | T2000 UVC Surface Disinfection |
| With the sterilAir T2000 Series surface disinfection modules, the UVC radiation is concentrated with the aid of a special reflector, and focused onto the surface to be disinfected. | |
| The T2000 series is available in different sizes. The standard unit is a total 911 mm in length, whilst the effective radiation range is around 765 x 75mm. The high-frequency electronics built into the unit guarantee a safety cut-out in the event of malfunctioning, and UV output remains steady even during mains-power fluctuations. | |
| Steril Air | T2002-IP UVC Surface Disinfection |
| This unit, completely manufactured from stainless steel or rustproof materials, is available in different designs/ upgrade levels. | |
| At the top upgrade level, the system is supplied with a water-repellent, fully encompassing IP64 housing. According to choice, the housing aperture is equipped with a window with a quartz pane, or with a special sheeting that is particularly tear-resistant and UV-permeable. At this upgrade level, the disinfection device is also fully usable under adverse conditions (high dust load, dripping water, etc.). | |
| Steril Air | T2004 UVC Surface Disinfection |
| The T2004 Surface Disinfection System is a unit of modular design which can be optimally adapted to any operating situation encountered. Starting with an appliance body only 35 mm wide per module, as many units as wished may be combined. Each of these modules is both a carrier and an independent supplier of an individual disinfection tube. | |
| At around 41°C, the heat emission of the radiation sources used is gratifyingly low, so that even heat-sensitive surfaces can be disinfected reliably and safely. | |
| Steril Air | T2005 UVC Surface Disinfection |
| The sterilAir T2005 is a robust, shock-resistant surface disinfection device whose UVC radiation sources are protected by a sturdy stainless-steel structure. This device not only serves to protect the tubes, but also meets statutory regulations prohibiting the use of unprotected radiation sources. | |
| Steril Air | AQD2048-C UVC Photoreactor |
| The sterilAir AQD2048-C is the smallest stainless-steel photoreactor in the AQD series. The reactor housing consists of an especially high-grade 4A stainless steel (WN.4571), double-pickled and passivated for increased resistance. | |
| At the conventional default dose of 400 J/m², the maximum water flow rate is 800 litres/ hr. The unit is connected to the existing pipe system via the ½-inch externally threaded nozzles, fitted on the sides at different heights. It is already fully functional in the illustrated design. Sensor-supported monitoring is recommended. | |
| Steril Air | AQD2075-C UVC Photoreactor |
| At a default dose of 400 J/m², this photoreactor is capable of safely disinfecting up to 1,400 litres/hr. The unit is connected to the existing pipe system via the ¾-inch externally threaded nozzles, fitted on the sides at different heights. | |
| The disinfection unit is delivered with a Swiss type-12 plug (standard), a two-pin earthed plug, or a 5m cable (not made up), as wished. It is already fully functional in the illustrated design. Sensor-supported monitoring is recommended. | |
| Steril Air | AQD2090-C UVC Photoreactor |
| The AQD2090-C disinfection system is a total 700mm in length and is capable of disinfecting up to 2,500 litres/hr. (default dose: 400 J/m²). The unit is connected to an existing pipe system via its ¾-inch externally threaded nozzles, fitted on the sides at different heights. | |
| The disinfection unit is delivered with a Swiss type-12 plug (standard), a two-pin earthed plug, or a 5m cable (not made up), as wished. It is already fully functional in the illustrated design. Sensor-supported monitoring is recommended. | |
| Steril Air | AQD2136-1 UVC Photoreactor |
| The sterilAir AQD2136-1 photoreactor housing is made of rustproof stainless steel (WN 1.4301) which is additionally pickled, passivated and glass-bead-radiated from the outside. | |
| The system is based on an energy-optimised sterilAir high-efficiency UVC tube with a particularly high output constancy. At the conventional default dose of 400 J/m², the maximum water flow rate is 3,000 litres/ hr. All safety functions of the system are monitored and controlled by the FCU2000 electronic control unit. | |
| Steril Air | AQD2158-1 UVC Photoreactor |
| The sterilAir AQD2158-1 largely corresponds to the AQD2136-1 model, although it boasts a performance-enhanced combination of electronic ballast and UVC tube capable of achieving higher disinfection efficiencies. | |
| All safety functions of the system are monitored and controlled by FCU2000 electronic control unit. At the conventional default dose of 400 J/m², the maximum water flow rate is 4,000 litres/hr. The reactor housing is made of stainless steel (WN 1.4301) which is additionally pickled, passivated and glass-bead-radiated from the outside. | |
| Steril Air | AQD2136-3 UVC Photoreactor |
| The sterilAir AQD2136-3 boasts three energy-optimised long-life, high-output-constancy UVC tubes, fed via three supply units which are completely independent of each another. At the conventional default dose of 400 J/m², the maximum water flow rate is 7,000 litres/hr. | |
| The sterilAir FCU2000 or UES2004-SE control units allow the operating status of each individual radiation source as well as the measuring result of the built-in UVC sensor to be recorded and displayed, both on site and via the optional remote-diagnosis connection. If required, individual radiation sources can be deliberately switched off and on. | |
| Steril Air | AQD2158-3 UVC Photoreactor |
| With a disinfection volume of up to 10,000 litres/ hr. (based on a radiation output of 400 J/m² after 8,500 operating hours), the sterilAir AQD2158-3 is currently the highest-output photoreactor in the AQD2100 series. | |
| The system boasts three completely independently working high-efficiency UVC tubes. The operating status of each individual radiation source as well as the measuring result of the built-in UVC sensor is recorded via the FCU2000 system control, either locally, or else optionally via the remote-diagnosis connection. If required, individual radiation sources can be deliberately switched off and on. | |
| Steril Air | AQD54-C UVC Photoreactor |
| The sterilAir AQD54-C is a compact system only 54cm long. Measured at a default radiation of 400 J/m², its disinfection efficiency is around 650 litres/hr. The system is connected via a 32 DN 25 bonding sleeve, although other connection means can be offered as an option. | |
| The semi-transparent reactor tube is UV-impervious, and enables a rapid operational check of the radiation source. As a matter of principle, we recommend monitoring the functioning of the system with a sterilAir UES2000-type control unit, although direct connection to the mains is also possible. | |
| Steril Air | AQD54 UVC Photoreactor |
| The sterilAir AQD54 is around 90cm long, and at the default radiation recommended for drinking water of 400 J/m², offers a maximum disinfection volume of approx. 1,500 litres/hr. | |
| The light-transparent reactor tube is impervious to short-wave UV radiation, and allows a rapid visual check of the built-in UVC radiation source. Connection to a sterilAir UES2000 increases operational safety. | |
| Steril Air | AQD64-C UVC Photoreactor |
| The AQD64-C is the short model of the AQD64 photoreactor. In contrast to the standard AQD64 model, it disinfects a flow volume of max. 1,100 litres/hr., measured at a radiation output of von 400 J/m². | |
| Connection to the water-supply main is via a 32 DN 25 bonding sleeve. The system can easily be operated at a permanent load of up to 6 bar. | |
| Steril Air | AQD64 UVC Photoreactor |
| The AQD64 model is the highest-efficiency system in the sterilAir plastic reactor series. The standard AQD64 model measures approx. 95cm in length, and offers a maximum disinfection volume of around 2,800 litres/hr., where the minimum radiation output is defined as 400 J/m². | |
| Steril Air | Immersion radiator AQT2000 |
| sterilAir immersion systems of the series AQT2000 are very easy to fit and maintain. A tube change is only necessary after 12''000 operating hours. There is no need for a support fitting in the water container and there are no complicated exterior constructions - simply position the system and switch it on! | |
| AQT2000 systems are IP68 tested and CE approved by the German TUV. It is recommended that the system is run using the monitoring system UES2000. When connected to the more sophisticated FCU2000 monitoring system there is an easy link up and software visualized control to the automatic facility management system. | |
| Steril Air | UVC Immersion Radiator TGL2000 |
| The TGL2000 immersion radiator is designed for the desinfection of enlarged cisterns, water tanks and ice water vessels – even for very cold temperatures. | |
| The device is based on a compact arrangement of 4 x 36W AQT2000 modules whereby in the heart of the media to be treated a very high UVC density is reached. | |
| Due to the suspension eye in centre position an easy installaion is possible – f.e. with one a steel chain or cable while only two cables need to be connected on a 220 V supply. |
Từ khóa gợi ý:
Đèn Uv Diệt Khuẩn Cực Tím
Đèn Cực Tím Diệt Khuẩn
Đèn Diệt Khuẩn Cực Tím
Đèn Tia Uv Diệt Khuẩn
Đèn Tia Cực Tím Diệt
Đèn Tia Cực Tím Uv
Đèn Uv Tia Cực Tím
Đèn Tia Cực Tím - Uv
Hệ Thống Đèn Cực Tím
Đèn Tím Diệt Khuẩn
Đèn Uv Diệt Khuẩn
Đèn Diệt Khuẩn Uv
Đèn Diệt Khuẩn - Uv
Đèn Uv Diệt Khuẩn Uv
Đèn Tia Cực Tím
Đèn Tia Cực Tím
Tia Cực Tím Diệt Khuẩn
Đèn Cực Tím Uv
Đèn Cực Tím Uv
Đèn Uv Cực Tím
HẾT HẠN
0938 047 734
| Mã số : | 7887664 |
| Địa điểm : | Hồ Chí Minh |
| Hình thức : | Cần bán |
| Tình trạng : | Hàng mới |
| Hết hạn : | 20/12/2020 |
| Loại tin : | Thường |
Để mua hàng an toàn trên Rao vặt, quý khách vui lòng không thực hiện thanh toán trước cho người đăng tin!
Gợi ý cho bạn
Bình luận