Tủ sấy Memmert Đức- Model UFP- 550

Standard equipment

Ventilation and Control

• forced air circulation by quiet air turbine adjustable in 10% steps via process controller, for each segment individually
• adjustment of pre-heated fresh air admixture by air flap through process controller in 10% steps for each segment individually
• vent connection with restrictor flap
• adaptive, fuzzy-supported, multifunctional, digital microprocessor PID-controller
• autodiagnostic system with fault indication
• 2 Pt100 sensors Class A in 4-wire-circuit, mutually monitoring and taking over the performance at the same temperature value
• digital 7-day-programme-timer with real time clock, precise minute setting, for one set value or start of ramp operation
• integrated timer for tempering profiles of up to 40 ramps, each segment adjustable from 1 min. up to 999 hours
• multifunctional programming via menu on 8-digit alphanumeric digital display (language to be chosen via set-up):
  tempering profiles of up to 40 ramps
  time- and set-point dependent operation
  air flap adjustable in 10% steps
  speed of air turbine in 10% steps
• digital display (LED) of all set parameters, such as temperature, weekdays, time, fan speed, air flap position, programme status and set-up values
• resolution of display for set value 0,1 °C below 99,9 °C, 0,5 °C above 100 °C; for actual value 0,1 °C
• long-term logging (ring store) of all relevant data, GLP-conforming as data logger - 1024 kB
• programme stored on power failure
• parallel printer interface (incl. real-time clock with date function) for printing logging files, suitable all PCL3-compatible ink-jet printers (USB available via converter, see accessories)
• serial interface RS 232 including MEMMERT Software "Celsius" for programming and documentation
• chip card control incl. one MEMoryCard XL with 32 kB (up to 40 ramps)
• incl. works calibration certificate for +160 °C

Multiple Overtemperature Protection

• with audible and visual alarm
• digitally adjustable, electronic microprocessor overtemperature controller TWW protection class 3.1 - maximum value for overtemperature - minimum value for undertemperature
• additional integral over- and undertemperature monitor "ASF" (Auto-Safety-Function) automatically following the setpoint value at a preset tolerance range; audible alarm is activated in case of over- or undertemperature, heating is switched off in case of overtemperature
• resolution of display and setting accuracy: 0,5 °C below 99,9 °C, 1 °C above 100 °C
• mechanical temperature limiter TB protection class 1 switching the heating off at approx. 10 °C above max. oven temperature

Textured Stainless Steel Casing

• w x h x d: 630 x 920 x 650 mm
• fully insulated stainless steel door with double locking and 4-point adjustment
• rear zinc-plated steel

Interior - Heating Concept

• w x h x d: 480 x 640 x 500 mm, 153 l
• easy-to-clean interior, made of stainless steel, reinforced by deep drawn ribbing with integrated and protected large-area heating on four sides
• 2 stainless steel grids

Temperature Range

• from +30 °C (however, at least 10 °C above ambient) up to +250 °C

Voltage / Power Rating

• 230 V (+/- 10%), 50/60 Hz
• ca. 2.200 W (during heating)
• adaption of effective heating power depending on the set temperature

Packing Data

• net weight approx. 91 kg
• gross weight carton approx. 127 kg
• dimensions approx.:
  carton w x h x d: 75 x 114 x 84 cm
• the appliances must be transported upright

Customs Tariff Number

• 8419 3990

Country of Origin

• Federal Republic of Germany

WEEE-Reg.-No.

• DE 66812464

Accessories

	Temperature range +300 °C for universal ovens (not available for ovens with glass door)		A0
	Perforated stainless steel shelf		E0(x)
	Stainless Steel Grid (for good air circulation)		E3(x)
	Interface USB instead of interface RS232		W3
	Interface Ethernet instead of RS232 inclusive software "Celsius Ethernet-Edition"		W4
	Parallel/USB converter cable with integrated power supply unit to connect PCL3-compatible HP printers with USB interface to MEMMERT units.		W1
	Documentation package consisting of parallel USB converter cable including PLC3-compatible HP colour inkjet printer with USB interface (HP Deskjet 6940 or successor) for direct connection of printer to Memmert unit		W2
	IQ check list with works test data for oven as support for validation by customer		Q1
	OQ check list including one free-selectable temperature distribution survey to DIN 12880: 2007-05 (size 200/300: 9 measuring points, size 400-800: 27 measuring points) with works test data for oven as support for validation by customer		Q2
	Software conforming to FDA "Celsius FDA-Edition" for up to 16 units		Q3
	Oven-linked authorisation card (User-ID-Card) - prevents undesired manipulation by unauthorised third parties		V1
	Computer interface RS485 (for networking a maximum of 16 ovens) instead of interface RS232		V2
	Temperature profile write/read unit for programming via PC, for writing to and reading from the chip card, up to 40 ramps		V3
	Additional chip card, blank, formatted (32 kB MEMoryCard XL for a maximum of 40 ramps)		V4
	Connection cable for computer interface RS232 according to DIN 12 900-1